This page was exported from Free Download Braindump2go Oracle OCA, OCP, OCM,Microsoft Exam Questions & Dumps with PDF&VCE [ http://www.oracledumps.com ] Export date:Sat Aug 24 4:06:49 2019 / +0000 GMT ___________________________________________________ Title: December/2018 Exam Pass 100%!Braindump2go 300-360 PDF and VCE 185Q Instant Download[Q118-Q128] --------------------------------------------------- December/2018 Braindump2go 300-360 Exam Dumps with PDF and VCE New Updated Today! Following are some new 300-360 Real Exam Questions:1.|2018 Latest 300-360 Exam Dumps (PDF & VCE) 185Q Download:https://www.braindump2go.com/300-360.html2.|2018 Latest 300-360 Exam Questions & Answers Download:https://drive.google.com/drive/folders/0B75b5xYLjSSNaFhjTjl4Uk0tbDg?usp=sharingQUESTION 118An engineer wants the controller to report when a client exceeds the minimum acceptable RSSI level, to ensure support for the minimum data rate required.Which controller option must be configured?A. Enable coverage hole detectionB. Enable the coverage optional mode.C. Set the DCA channel sensitivity to high.D. Set the coverage exception level per AP to 0.Answer: AExplanation:If clients on a lightweight access point are detected at threshold levels (RSSI, failed client count, percentage of failed packets, and number of failed packets) lower than those specified in the RRM configuration, the access point sends a "coverage hole" alert to the controller. The alert indicates the existence of an area where clients are continually experiencing poor signal coverage, without having a viable access point to which to roam. The controller discriminates between coverage holes that can and cannot be corrected. For coverage holes that can be corrected, the controller mitigates the coverage hole by increasing the transmit power level for that specific access point. The controller does not mitigate coverage holes caused by clients that are unable to increase their transmit power or are statically set to a power level because increasing their downstream transmit power might increase interference in the https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-0/configuration/guide/c70/c70rrm.htmlQUESTION 119During an installation of a wireless network in a country that follows ETSI standards, the customer is requesting to manually set the channels on the 2.4GHz radios. Which channels are recommended for use in this deployment?A. 52, 56, 60, 64B. 1, 6, 11, 14C. 36, 40, 44, 48D. 1, 5, 9, 13Answer: DExplanation: QUESTION 120A customer wants to upgrade their current wireless infrastructure to support wireless voice capabilities. When using a voice readiness assessment tool, the customer notes that multiple areas have failed to meet the requirementsHow should the customer resolve this issue?A. Reduce the maximum threshold on the voice readiness tool to -67 dBm.B. Perform a site survey to position access points in the facility?C. Ensure that there is a 1 to 5 ratio of monitor mode to local mode access pointsD. Increase the power on all the access points to 25mW or more.Answer: AExplanation:https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/WiFiLBS-DG/wifich5.htmlQUESTION 121You are designing an outdoor mesh network to cover several sports fields. The core of the network is located in a building at the entrance of a sports complex. Which type of antenna do you use with the RAP for backhaul connectivity?A. a 5 GHz, 14-dBi patch antennaB. a 5 GHz, 8-dBi omnidirectional antennaC. a 2.4 GHz, 14-dBi omnidirectional antennaD. a 2.4 GHz, 8-dBi patch antennaAnswer: BExplanation:The AP1524PS includes three radios: a 2.4-GHz, a 5.8-GHz, and a 4.9-GHz radio. The 2.4-GHz radio is for client access (non-public safety traffic) and the 4.9-GHz radio is for public safety client access traffic only. The 5.8-GHz radio can be used as the backhaul for both public safety and non-public safety traffic. https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-6/configuration-guide/b_cg76/b_cg76_chapter_010000001.htmlQUESTION 122An engineer is preparing for an active site survey of a warehouse and is informed that they should not enter any areas that are blocked by supplies that are difficult to move. Which option describes how the engineer should address this restriction?A. Utilize a predictive tool to define coverage in off-limits areas.B. Educate the customer about the importance of accurate and complete measurementsC. Extrapolate restricted access areas by drawing circles for AP coverage.D. Survey hallways, common areas, and storerooms.Answer: AQUESTION 123Which description of the ideal VoWLAN design is true?A. smaller cells with all data rates enabled to ensure that all clients can associateB. larger cells with higher data rates enabled and WPA2 to secure voice conversationsC. smaller cells with higher data rates enabled and admission control enabled through WMMD. smaller cells with higher data rates enabled and no overlap to prevent co-channel interferenceAnswer: CQUESTION 124A wireless engineer is hired to troubleshoot wireless network issues and discovers that the customer is using 802 11 ac access points with 80 MHz-wide channels in a high-density environment.Which solution addresses these issues?A. Disable RRM on the WLC.B. Disable TPC on the WLCC. Decrease the channel width.D. Increase the minimum data rate supportedAnswer: CQUESTION 125A customer has determined that a cable run for a low-throughput RF design is not economically feasible to install.Which two access point modes can alleviate these customer concerns? (Choose two.)A. bridgeB. snifferC. Flex+BridgeD. FlexConnectE. localAnswer: ADQUESTION 126An engineer is concerned with the compliance guidelines for human exposure to a rooftop RF transmitter that has been recently installed.What regulation should be reviewed to ensure proper certification?A. OSHA 1910.97B. FCC QET Bulletin 65C. NFPS Article 810D. SCEE Section 28.1Answer: BExplanation:Evaluating Compliance With FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields; This revised OET Bulletin 65 has been preparedhttps://www.fcc.gov/general/oet-bulletins-lineQUESTION 127You must redesign an existing wireless network that spans multiple floors to support location-based services.Where do you install the access points?A. in the elevatorsB. in the perimeter of each floorC. in the stairwells of each floorD. in the center of each floorAnswer: BExplanation:In a location-ready design, it is important to ensure that access points are not solely clustered in the interior and toward the center of floors. Rather, perimeter access points should complement access points located within floor interior areas. In addition, access points should be placed in each of the four corners of the floor, and at any other corners that are encountered along the floor perimeter. These perimeter access points play a vital role in ensuring good location fidelity within the areas they encircle, and in some cases may participate in the provisioning of general voice or data coverage as wellhttps://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/WiFiLBS-DG/wifich5.htmlQUESTION 128You are designing a wireless mesh network for an oil refinery. What is the Cisco-recommended model of a Cisco Aironet 1550 Series Outdoor Access Point for this location?A. 1552IB. 1552CUC. 1552ED. 1552HAnswer: DExplanation:Cisco Aironet 1552H Access PointThis ruggedized, outdoor, 802.11n access point is suitable for generic hazardous environments, and does not require a wireless sensor network.https://www.cisco.com/c/en/us/products/wireless/aironet-1550-series/index.html!!!RECOMMEND!!!1.|2018 Latest 300-360 Exam Dumps (PDF & VCE) 185Q Download:https://www.braindump2go.com/300-360.html2.|2018 Latest 300-360 Study Guide Video: YouTube Video: YouTube.com/watch?v=1MSGk2z6Rd8 --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2018-12-28 06:27:08 Post date GMT: 2018-12-28 06:27:08 Post modified date: 2018-12-28 06:27:08 Post modified date GMT: 2018-12-28 06:27:08 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com